Microbial Limit Test (USP <61> and <62>): Procedure, Media, Incubation and Acceptance Criteria

Quick answer: The microbial limit test (MLT) is how the microbiological quality of a nonsterile product is checked. USP splits it into two general chapters. USP <61> counts the bacteria and fungi that grow aerobically: the total aerobic microbial count (TAMC) and the total combined yeasts and molds count (TYMC). USP <62> checks for the absence, or limited occurrence, of specified microorganisms such as Escherichia coli, Salmonella, Pseudomonas aeruginosa and Staphylococcus aureus. The acceptance criteria that most labs apply come from USP <1111>.

This guide follows the harmonized texts, which match Ph. Eur. 2.6.12 and 2.6.13 and JP 4.05. It explains how the test works; release testing must follow the current official chapter and a validated procedure.

USP <61> and <62> at a glance

USP <61> Microbial Enumeration Tests USP <62> Tests for Specified Microorganisms
Question answered How many aerobic bacteria and fungi are present? Is a particular objectionable organism present?
Result TAMC and TYMC in cfu/g or cfu/mL Absent or present in a stated amount (bile-tolerant Gram-negative bacteria can also be estimated)
Methods Membrane filtration, pour plate, surface spread, most-probable-number (MPN) Enrichment, then selective or indicative media, then identification
Main media Soybean–Casein Digest Agar (SCDA) and Sabouraud Dextrose Agar (SDA) Soybean–Casein Digest Broth plus organism-specific media (MacConkey, RVS, XLD, cetrimide, mannitol salt, VRBG, Columbia, SDA)
Not applicable to Products that contain viable microorganisms as active ingredients

Preparing the sample

Unless otherwise directed, 10 g or 10 mL of product is tested, taken from several containers so that the sample represents the batch. Smaller amounts are allowed in a few situations. One example is when the active substance is 1 mg or less per dosage unit, or per g or mL. Another is a batch of less than 1,000 g or 1,000 mL, where the amount is 1% of the batch unless a smaller amount is justified. Aerosols and transdermal patches are sampled as 10 containers or 10 patches.

  • Water-soluble products: dissolve or dilute, usually 1 in 10, in Buffered Sodium Chloride–Peptone Solution pH 7.0, Phosphate Buffer Solution pH 7.2 or Soybean–Casein Digest Broth. Adjust to pH 6–8 if needed.
  • Nonfatty products insoluble in water: suspend 1 in 10 in the same diluents. A surfactant such as polysorbate 80 at 1 g/L can help wetting.
  • Fatty products: dissolve in sterile-filtered isopropyl myristate, or mix with the minimum amount of sterile polysorbate 80. Warm to no more than 40 °C (45 °C in exceptional cases) and dilute 1 in 10 in prewarmed diluent.
  • Transdermal patches: remove the release liners and shake the patches in diluent containing suitable inactivators for at least 30 minutes.

Removing antimicrobial activity

Preservatives and active ingredients can kill or inhibit the organisms the test is trying to find. If the product has antimicrobial activity, it must be removed or neutralized, and any neutralizer used must be shown to be effective and not toxic to microorganisms. Common options from the chapter are:

Interfering substance Neutralizing agent or method
Phenolics, alcohol, aldehydes, sorbate Dilution
Quaternary ammonium compounds (QACs), parabens, bis-biguanides Lecithin
QACs, iodine, parabens Polysorbate
Aldehydes Glycine
Glutaraldehyde, mercurials Sodium bisulfite
Mercurials Thioglycollate
Mercurials, halogens, aldehydes Thiosulfate
EDTA Magnesium or calcium ions

Membrane filtration with rinsing is another way to separate organisms from an inhibitory product.

USP <61>: microbial enumeration methods

Membrane filtration

Filter a quantity of sample equivalent to 1 g or 1 mL of product (less if a high count is expected) through a membrane with a pore size of not more than 0.45 µm. Rinse the membrane with a suitable diluent, then place one membrane on SCDA for TAMC and another on SDA for TYMC.

Pour plate

For a 9 cm Petri dish, add 1 mL of the prepared sample and 15–20 mL of molten SCDA or SDA held at no more than 45 °C. Use at least two dishes for each medium and dilution.

Surface spread

Pour 15–20 mL of agar into each dish, let it set and dry the surface, then spread at least 0.1 mL of the prepared sample. Again, use at least two dishes per medium.

Most-probable-number (MPN) method

MPN is the least precise method and is used only for TAMC when no other method is suitable. It can be the right choice for some products with a very low bioburden. Prepare at least three serial tenfold dilutions, inoculate three tubes of Soybean–Casein Digest Broth at each level, incubate at 30–35 °C for up to 3 days, and read the MPN from the table in the chapter. It is not reliable for molds.

Media, incubation and countable plates

Count Medium Incubation (product test) Plates used for the count
TAMC Soybean–Casein Digest Agar 30–35 °C for 3–5 days Highest number of colonies, up to 250 per plate
TYMC Sabouraud Dextrose Agar 20–25 °C for 5–7 days Highest number of colonies, up to 50 per plate

Calculating TAMC and TYMC

The TAMC is the number of colonies on SCDA. Any fungal colonies on SCDA are counted as part of the TAMC. The TYMC is the number of colonies on SDA, and any bacterial colonies on SDA are counted as part of the TYMC. If bacteria on SDA are expected to push the TYMC over its limit, SDA containing antibiotics may be used.

Worked example (pour plate): 10 g of a tablet product is suspended in 90 mL of diluent (1 in 10). Two SCDA plates, each with 1 mL, give 23 and 27 colonies. The mean is 25 cfu per mL of the 1 in 10 suspension, so TAMC = 25 × 10 = 250 cfu/g. If the specification is 103 cfu/g, the result complies.

When an acceptance criterion is written as a power of ten, it is interpreted as follows:

  • 101 cfu: maximum acceptable count = 20
  • 102 cfu: maximum acceptable count = 200
  • 103 cfu: maximum acceptable count = 2,000, and so forth.

Growth promotion and method suitability for <61>

Before a product is tested, the media must be shown to support growth and the method must be shown to recover organisms in the presence of that product. Suitability must be confirmed again if the test or the product changes in a way that could affect the result.

Test strain (example) TAMC (SCDA, 30–35 °C) TYMC (SDA, 20–25 °C)
Staphylococcus aureus ATCC 6538 ≤ 3 days —
Pseudomonas aeruginosa ATCC 9027 ≤ 3 days —
Bacillus subtilis ATCC 6633 ≤ 3 days —
Candida albicans ATCC 10231 ≤ 5 days ≤ 5 days
Aspergillus brasiliensis ATCC 16404 ≤ 5 days ≤ 5 days
  • Inoculum: not more than 100 cfu, using cultures no more than five passages from the master seed lot.
  • Acceptance: on solid media, the count must not differ by a factor greater than 2 from the calculated value of the standardized inoculum. The same factor-of-2 rule applies when the product is present.
  • Negative control: diluent only. There must be no growth, and a failed negative control needs an investigation.

USP <62>: tests for specified microorganisms

For each organism, the sample is first enriched in a nonselective broth so that injured cells can recover. It is then moved to a selective broth or plate, and any suspect colonies are confirmed by identification tests. The product complies if no suspect colonies grow or if the identification tests are negative.

Organism Sample and pre-incubation Selective step What a suspect result looks like
Escherichia coli Amount equal to 1 g or 1 mL in Soybean–Casein Digest Broth (SCDB), 30–35 °C, 18–24 h 1 mL into 100 mL MacConkey Broth, 42–44 °C, 24–48 h; subculture on MacConkey Agar, 30–35 °C, 18–72 h Growth of colonies on MacConkey Agar
Salmonella At least 10 g or 10 mL in SCDB, 30–35 °C, 18–24 h 0.1 mL into 10 mL Rappaport Vassiliadis Salmonella Enrichment Broth, 30–35 °C, 18–24 h; subculture on XLD Agar, 30–35 °C, 18–48 h Well-developed red colonies, with or without black centres
Pseudomonas aeruginosa Amount equal to 1 g or 1 mL in SCDB, 30–35 °C, 18–24 h Subculture on Cetrimide Agar, 30–35 °C, 18–72 h Growth of colonies
Staphylococcus aureus Amount equal to 1 g or 1 mL in SCDB, 30–35 °C, 18–24 h Subculture on Mannitol Salt Agar, 30–35 °C, 18–72 h Yellow or white colonies surrounded by a yellow zone
Clostridia Two portions of at least 1 g or 1 mL; heat one at 80 °C for 10 min and cool rapidly 10 mL of each into 100 mL Reinforced Medium for Clostridia, anaerobic, 30–35 °C, 48 h; subculture on Columbia Agar, anaerobic, 30–35 °C, 48–72 h Anaerobic growth of rods, with or without endospores, that are catalase-negative
Candida albicans Amount equal to at least 1 g or 1 mL in 100 mL Sabouraud Dextrose Broth, 30–35 °C, 3–5 days Subculture on Sabouraud Dextrose Agar, 30–35 °C, 24–48 h White colonies
Bile-tolerant Gram-negative bacteria 1 in 10 dilution in SCDB at 20–25 °C for about 2 h (not more than 5 h), to resuscitate without multiplying Enterobacteria Enrichment Broth Mossel, 30–35 °C, 24–48 h; subculture on Violet Red Bile Glucose Agar, 30–35 °C, 18–24 h Growth of colonies

Quantitative test for bile-tolerant Gram-negative bacteria

When a limit rather than absence is required, Mossel broth is inoculated with amounts of product equal to 0.1 g, 0.01 g and 0.001 g (or mL). After subculture on VRBG agar, the probable number per gram is read from the pattern of positive results:

0.1 g 0.01 g 0.001 g Probable number (cfu per g or mL)
+ + + More than 103
+ + − Less than 103 and more than 102
+ − − Less than 102 and more than 10
− − − Less than 10

Suitability of the <62> methods

Each medium is checked for its growth-promoting, inhibitory and indicative properties. For example, MacConkey Broth must grow E. coli and inhibit S. aureus, and Mannitol Salt Agar must grow and indicate S. aureus while inhibiting E. coli. Growth-promotion checks use not more than 100 cfu, and inhibition checks use at least 100 cfu. Typical strains are E. coli ATCC 8739, Salmonella enterica serovar Typhimurium ATCC 14028, P. aeruginosa ATCC 9027, S. aureus ATCC 6538, Clostridium sporogenes ATCC 11437 or 19404, and C. albicans ATCC 10231.

For method suitability, the product is inoculated with not more than 100 cfu of the relevant organism. The test is then run using the shortest incubation period given, and the organism must be detected with the expected reactions.

Acceptance criteria (USP <1111>)

Chapters <61> and <62> give the methods. The limits usually come from the product monograph, the approved specification or USP <1111>. The harmonized limits for nonsterile dosage forms are:

Route of administration TAMC (cfu/g or cfu/mL) TYMC (cfu/g or cfu/mL) Specified microorganisms
Nonaqueous preparations for oral use 103 102 Absence of E. coli (1 g or 1 mL)
Aqueous preparations for oral use 102 101 Absence of E. coli (1 g or 1 mL)
Rectal use 103 102 —
Oromucosal, gingival, cutaneous, nasal and auricular use 102 101 Absence of S. aureus and P. aeruginosa (1 g or 1 mL)
Vaginal use 102 101 Absence of P. aeruginosa, S. aureus and C. albicans (1 g or 1 mL)
Transdermal patches (limits per patch) 102 101 Absence of S. aureus and P. aeruginosa (1 patch)
Inhalation use 102 101 Absence of S. aureus, P. aeruginosa and bile-tolerant Gram-negative bacteria (1 g or 1 mL)
Substances for pharmaceutical use 103 102 —

The list of specified organisms is not exhaustive. Depending on the starting materials, the process and the patients, other organisms may also be objectionable and need to be assessed.

Common mistakes

  • Skipping method suitability. A clean result from a product with preservatives means little if recovery in the presence of that product was never shown.
  • Leaving yeasts out of the TAMC. Fungal colonies on SCDA belong in the TAMC; bacterial colonies on SDA belong in the TYMC.
  • Counting the wrong plates. Use the dilution with the highest count below 250 (TAMC) or 50 (TYMC) colonies per plate.
  • Forgetting the dilution factor. Counts from a 1 in 10 suspension must be multiplied by 10 (or by the dilution used) to give cfu per g or mL.
  • Overheating fatty products. Warming above 40 °C (45 °C exceptionally) can kill the organisms the test is meant to count.
  • Long resuscitation for bile-tolerant Gram-negatives. The 20–25 °C pre-incubation is meant to revive organisms without letting them multiply, so keep it to about 2 hours and no more than 5.
  • Testing only what the table lists. The specified organisms are a minimum; objectionable organisms depend on the product and its use.

For sterile products the test is different; see sterility testing in pharmaceutical microbiology. For a colony-counting approach in food, see aerobic plate count in food, and for confirming suspect colonies, see Gram staining.

Frequently Asked Questions (FAQs)

What is the microbial limit test?

It is the microbiological examination of nonsterile products. It combines a count of aerobic bacteria and fungi (USP <61>) with tests for specified microorganisms (USP <62>), and the results are compared with acceptance criteria such as those in USP <1111>.

What is the difference between USP <61> and USP <62>?

USP <61> is quantitative: it gives the TAMC and TYMC in cfu/g or cfu/mL. USP <62> is mainly qualitative: it shows whether specified organisms such as E. coli, Salmonella, P. aeruginosa, S. aureus, Clostridia or C. albicans are present.

What media and incubation are used for TAMC and TYMC?

TAMC uses Soybean–Casein Digest Agar at 30–35 °C for 3–5 days. TYMC uses Sabouraud Dextrose Agar at 20–25 °C for 5–7 days.

How much sample is used in the microbial limit test?

Usually 10 g or 10 mL, normally prepared as a 1 in 10 dilution. Smaller amounts are allowed for very potent products and for very small batches.

What does an acceptance criterion of 102 cfu/g mean?

It means the maximum acceptable count is 200 cfu/g. Likewise, 101 allows up to 20 and 103 allows up to 2,000.

Which organisms are used for growth promotion in USP <61>?

S. aureus, P. aeruginosa and B. subtilis for TAMC, plus C. albicans and A. brasiliensis for both TAMC and TYMC, each at not more than 100 cfu.

Why is the sample heated to 80 °C in the Clostridia test?

Heating one portion at 80 °C for 10 minutes kills vegetative cells but not spores, so growth from the heated portion points to spore-forming Clostridia.

References

Incubation times, media and limits are summarised from the harmonized chapters for education. Testing must follow the current official USP–NF text, the product specification and a validated method.

Related guide: the arithmetic behind TAMC and TYMC results, including dilution factors, countable plate ranges and averaging duplicate plates, is worked through in Total Viable Count (TVC): Plate Count Method, Formula and Calculation.

Leave a Comment

Your email address will not be published. Required fields are marked *